A walk in closet in Dubai with custom joinery adds AED 30,000 to AED 80,000 to a villa renovation, according to LC Interiors’ villa renovation costs guide. A standard built-in wardrobe runs AED 8,000 to AED 25,000. The expensive failure is smaller than either number: a drawing issued before anyone measured your walls.
Most bespoke wardrobe disputes start on paper, not in the workshop. A Dubai interior design studio that records the site measure first removes the cause.
How much does a walk in closet cost in Dubai?
LC Interiors’ villa guide puts custom walk-in dressing rooms at AED 30,000 to AED 80,000 on top of the bedroom budget. Built-in wardrobes with MDF carcassing and acrylic doors sit at AED 8,000 to AED 25,000, depending on size and finish.
The spread comes from material grade and detail, not square metres alone. The studio’s budget guide notes that bespoke joinery is quoted in running metres but detailed per panel, so every extra feature adds drawing and finishing hours.
Fix the closet list early and price it as a package.
LC Interiors treats any later “make this one bespoke too” request as a formal variation with a number attached, and the villa guide warns that a change order adds 15% to 30% to that item.
Why does a 15 mm ceiling slope ruin a custom wardrobe in Dubai?
LC Interiors’ joinery shop drawings guide says walls in Dubai villas and apartments routinely deviate 10 to 25 millimetres from plan over a three-metre run, and ceilings are rarely level.
Take a full-height wardrobe drawn at 2,800 millimetres. If the ceiling falls 15 millimetres at one end, that unit either scribes to the ceiling or fails.
The drawing has to say which. When it stays silent, whoever holds the board on site makes the call.
A recorded site measure prevents that. The guide asks for wall deviations in both directions, finished floor levels, ceiling high and low points, air conditioning grilles, sprinkler heads and any skirting or cornice the joinery must meet.
No joinery drawing should be final before that survey exists.
What should the shop drawing state for fitted wardrobes in Dubai?
The studio’s guide lists the gaps it keeps finding in packages sent to it, and each one is cheap to fix on paper and costly to fix in the workshop.
- Dimensions taken to the finished plaster level, not the structural wall.
- Toe kick height written down, because an assumed height gets decided by whoever is holding the material.
- Veneer direction held consistent across every sheet of a tall unit.
- A named hardware model for hinges, runners and handles, since “soft-close hinge” is not a specification.
Once the drawing is approved, LC Interiors’ timeline guide puts bespoke joinery at five to eight weeks in a decent Sharjah or Al Quoz workshop. A remake costs you that time as well as the money.
The full detail set is explained in the studio’s joinery shop drawings guide.
Does every wardrobe in the house need to be bespoke?
No. LC Interiors argues that a master dressing room earns bespoke joinery because its proportions are specific to the room and to you.
A children’s wardrobe wall can use a good imported system behind a bespoke fascia, at roughly forty percent of the cost. The seam stays invisible when the same workshop matches the fascia, handles and colour.
Decide this at concept stage. The studio’s custom furniture and carpentry service covers fitted wardrobes and walk-in closets, so one team can draw the bespoke dressing room and the matched fronts together.
For dressing room design, the same rule applies to extras. If your plan includes shelf lighting, a central island or a dressing table, the outlet and lighting positions belong on the drawing before production, because outlets that land mid-panel get moved twice.
What should you check before the joinery goes in?
Glass is the line most owners price too late. LC Interiors’ material budget guide says mirrored wardrobes and glass panels are priced per cut-out and per polished edge, after the layout is final.
The guide describes clients finding at installation that moving one socket two hundred millimetres re-tempered an entire glass panel. Freeze the electrical layout before glass is ordered.
Paint comes before joinery where possible, so wardrobes install onto finished walls. The studio’s sequencing guide for occupied apartments gives the order: plaster repairs, tiling, gypsum and paint, then joinery install.
Then snag the joinery properly. The studio’s handover guide says to check every door and drawer for alignment and soft-close, and to expect 150 to 300 items on a typical apartment fit-out at first walkthrough.
A short list usually means a short inspection. Hold retention, typically 5 per cent, until the fixes are rechecked.
Before you sign, ask your designer three questions. Has the site measure been recorded?
Does the drawing say whether each full-height unit scribes or fails against the ceiling? Are the dimensions taken to finished plaster?
Common questions
How much does a walk in closet cost in Dubai?
According to LC Interiors’ villa renovation costs guide, a walk in closet in Dubai with custom joinery adds AED 30,000 to AED 80,000. A standard built-in wardrobe with MDF carcassing and acrylic doors costs AED 8,000 to AED 25,000, depending on size and finish.
Do I need a site measure before ordering a custom wardrobe in Dubai?
Yes. LC Interiors says no joinery drawing should be final before a recorded site measure for a custom wardrobe in Dubai. Walls routinely deviate 10 to 25 millimetres over a three-metre run, and ceilings are rarely level, so the drawing must show how the unit absorbs that.
Which wardrobes should be bespoke and which can be imported?
LC Interiors recommends bespoke for the master dressing room, where proportions are specific to the room. For fitted wardrobes in children’s rooms, a good imported system behind a bespoke fascia costs roughly forty percent as much, and the seam stays invisible when one workshop matches the fronts.
Why are mirrored wardrobe doors and glass fronts expensive?
LC Interiors’ material budget guide explains that glass is priced per cut-out, polished edge and custom bend after the layout is final. A late socket move can force a whole panel to be re-tempered. Freeze the electrical layout of your walk in closet in Dubai before glass is ordered.
